Accessories for fiber optics

For full-fledged work with fiber optics, in addition to welding and measuring equipment, various accessories are needed, for example: patch cords, pigtails, connecting sockets (optical adapters), connectors, attenuators, terminators, splitters, etc. For fiber optic welding, you also need a set of special tools for cutting fiber optic cable.

Tehencom company supplies a large number of accessories for fiber optics.

Below are the most popular accessories. Regarding prices and delivery times for the entire range of instrumentation, simply call us or write to us at E-mail and we will be happy to answer your questions.

Model A photo Short description
Accessories for fiber-optic communication lines (FOCL) of the EXFO company
EXFO FLS-240 - Visual Fault Locator - Flaw Detector

Product code: 1000353

Visual damage locator - flaw detector.
Bright red laser at 635 nm. 50 hours of battery life. Pulse and continuous modes. Universal connector for 2.5 mm or 1.25 mm diameters.
EXFO LFD-300/TG-300 FiberFinder - active fiber identifier with built-in tone generator

Product code: 1000349

Active fiber identifier with built-in tone generator LFD-300/TG-300 FiberFinder. Combines 3 test instruments in one housing: Active Fiber ID, Active Fiber Detector, Dark Fiber ID.
EXFO VCS-20A - Multifunctional optical phone.

Product code: 1000375

Multifunctional optical phone.
Four tools in one. Crystal clear, full duplex communications. Conference call. 3 power modes: battery, 9V battery, AC adapter/charger. Dynamic range: 50 dB.
EXFO FCD-10B - Clip-on connector at fiber bend.

Product code: 1000376

Connection device on the fiber bend of the "clothespin" type.
The connection does not require cutting or damaging the fiber.
Controlled by optical telephones at 1310 and 1550 nm.
Losses less than 6 dB. Completely passive device.
Accessories for fiber-optic communication lines (FOCL) of the Fujikura company

from stock
Fujikura FID-25R, FID-26R - Active fiber identifiers (identifiers)

Product code: 1000377

Active fiber identifiers Fujikura FID-25R, FID-26R
Determine the presence and type of signal in a single-mode fiber (without breaking the fiber).
Types of detected signals: traffic signal, continuous signal, modulated signal with a frequency of: 270 Hz, 1 kHz and 2 kHz. Wavelengths of the determined signals: from 900 to 1700 microns.
IDs can connect to pigtails and patch cords: 1.1mm; 1.5 mm; 1.7mm; 2 mm; 3 mm, as well as to bare fiber (0.25 mm), single and tape (up to 12 fibers).
Model FID-25R also contains a built-in power meter at 1310, 1490 and 1550 nm.
Measures the power of signals up to +10 dBm with an accuracy of ±0.3 dB.
Operating temperature range: from -10°С to +50°С. Weight: 180 g.
Power: up to 8 hours on two standard AA batteries.
Inexpensive, reliable identifiers with a large set of functions
Various accessories for fiber optic communication lines (FOCL)
Patchcords Patchcords Regular patch cords and master patch cords
Connectors: FC, SC, LC, ST, SMA, E2000, D4, LX.5, DIN, FDDI, Lemo, MPO, MTP, MTRJ, MU, MT in any combination.
Polishing type: SPC, UPC, APC (single-mode), PC (multi-mode).
Fiber type: SM-singlemode (9/125), MM-multimode OM1 (62.5/125), OM2 (50/125), OM3 (50/125).
Cable type: simplex, duplex, reinforced duplex.
Optical adapters Optical adapters Optical adapters (loop through connectors)
Types: FC, SC, LC, ST, SMA, E2000, D4, LX.5, DIN, FDDI, Lemo, MPO, MTP, MTRJ, MU, MT in various combinations.
Type of polishing connected connectors: PC or APC.
Type of fiber connected connectors: SM-single-mode, MM-multimode.
Type of connected cables: simplex, duplex.
Bare Fiber Adapters (BFA) Bare Fiber Adapters (BFA) Bare Fiber Adapters (BFA)
Connector types: FC, SC, LC, ST, MU, etc.
Designed for quick mechanical connection to SM and MM optical fiber with 250 or 900 microns coating. To connect, you need to strip (up to a diameter of 125 microns) and chop the fiber, and then insert and fix it in the adapter. Insertion loss: less than 1 dB.
Permanent optical attenuators Permanent optical attenuators Permanent optical attenuators
Standard damping values: 5; ten; fifteen; twenty; 25; 30 dB.
Connector types: FC, SC, LC, ST, DIN, MU, etc.
Polishing type: PC or APC.
Designed to introduce a fixed attenuation in a fiber optic line, for example, for the safe connection of measuring devices.
Kimwipes lint-free wipes Kimwipes lint-free wipes Kimwipes lint-free wipes
Quantity per package: 280 pcs.
Designed for cleaning the fiber from dust and varnish residues, as well as degreasing the fiber immediately before chipping. Moisten the cloth with alcohol before use.
Napkin size: 11 x 21 cm. Package size: 12 x 7.5 x 12 cm.
A set of tools
for mounting VOK
A set of tools for mounting VOK NIM-25 A set of tools for mounting VOK NIM-25
Tool kit includes: 1. Ripley-Miller CFS-2 stripper (for removing varnish from fibers; two positions: 0.25 mm and 2-3 mm) 2. Ripley-Miller RCS-114 stripper (for removing plastic sheath 4.5 -29 mm) 3. Stripper IDEAL 45-162 (for cutting optical modules) 4. Kevlar shears Ripley-Miller KS-1 5. Stripper Ripley-Miller 721 (for wires 0.6 - 2.6 mm) 6. Wires FIS F1-8265 (for cleaning the centers of ferrule connectors; 8 pcs. in a flask) 7. Alcohol pump-dispenser 8. Kimwipes EX-L wipes (1 pack = 280 pcs.) 9. Hydrophobic fiber cleaning liquid (1 liter ) 10. Cable cutter (length 350 mm, cable up to 6 mm) 11. Side cutters (nippers) 12. Pliers 13. Stripping knife with spare blades 14. Screwdriver set 15. Voltage indicator screwdriver 16. Hacksaw 17. Tape measure, 5m 18. Tweezers 19. Loupe 20.Insulating tape 21. Headlamp 22. Self-adhesive markers with numbers 23. Marker for writing 24. Consumables organizer 25. Tool case